1.實驗臺的臺面平整、光滑,需求邊沿切開規整,四邊平直,無顯著凹凸表象.貼面和封邊部件嚴密、平整,不允許有脫膠、鼓泡、洼陷、壓痕、表面劃傷、麻點、裂痕、崩角和刀口等
1. The table is flat and smooth with regular cutting edge and straight four sides without obvious concave and convex appearance. The veneer and sealing parts are tight and flat. No degumming, bubbling, depression, indentation, surface scratches, pitting, cracks, collapse angle and knife edge are allowed.
2.各涂層平均,鋼制或木制板表面平整,五色差、無拼接、無顯著凹凸、駁、無劃痕、無碰傷等殘損.切開、鉆孔和倒角無毛刺,表面的圓角、倒棱平均共同
2. On average, the surface of steel or wood panels is flat, with five-color difference, no splicing, no obvious concave and convex, no mottle, no scratch, no bruise and other damages. Cutting, drilling and chamfering have no burrs, and the rounded and chamfered surfaces are common on average.
3.柜體的每一塊,其四個邊有必要用熱熔膠經高溫高壓作防水封邊處置
3. It is necessary for each side of the cabinet to be treated with high-quality hot-melt adhesives as waterproof seals at high temperatures and pressures.
4.柜體的板塊與板塊之間的銜接,選用三合一內預埋銜接件,在放置三合一銜接件的"L"形孔洞的兩頭有必要注滿黃膠,以加強握釘力,抗彎弧變形、防滲水、防搖擺.并一同運用滾花木質圓棒棰,帶膠安穩加固銜接
4. The connection between the plate and the plate of the cabinet body should be made by using high-quality three-in-one pre-embedded joints and filling yellow glue at both ends of the L-shaped hole where the three-in-one joints are placed in order to strengthen the nail holding force, resist bending and arc deformation, prevent seepage and prevent swaying. The joints should be securely strengthened by rolling wooden round sticks with glue.
5.柜體的板塊與五金配件之間的銜接,在穩固一切螺釘之前,有必要打一個小于螺釘直徑和長度的孔,高壓寫入膠水后,再行擰入螺釘,以加強握釘力,如為螺釘與螺母銜接可在外
5. Before fixing all the screws, it is necessary to drill a hole smaller than the diameter and length of the screw. After high pressure writing into glue, the screw is screwed in to strengthen the grip force. If the screw is connected with the nut, it can be outside.
6.一切柜體銜接堅固,無松動表象;表面平整無顯著變形;顯露有些無毛刺及尖利矛頭
6. All cabinets are firmly connected and free from loosening; their surfaces are smooth and without significant deformation; some of them are burr-free and sharp spearheads are exposed.
7.零部件無開裂或劈裂表象,不會(huì )呈現影響運用1.功用的磨損變形表象,可動有些(例如可調式地腳、活動隔板等)活動靈敏,用手掀壓不會(huì )呈現永世形變形或松動,抗壓才干契合實驗臺的需求
7. Parts without cracking or splitting will not show the wear and deformation appearance that affects the use of 1. Functions. Movable parts (such as adjustable foot, movable partition, etc.) are sensitive to movement. Hand-lifting will not show permanent deformation or loosening. Compressive ability meets the needs of the test-bed.
8.單相三線電源插座與兩線插頭相兼容
8. Single-phase three-wire power socket compatible with two-wire plug
9.一切水、電、氣路需求平安、適用,并躲藏式安裝
9. All water, electricity and gas circuits need safe, applicable and hiding installation.
10.產物尺度需求:長、寬、高過失點≤3mm;鄰邊筆直度:臺面對角線、構造對角線1000mm≤3mm; 2000mm≤4mm; 3000mm≤
10. Product size requirement: length, width and high fault point < 3mm; adjacent edge straightness: mesa diagonal line, structural diagonal line 1000mm < 3mm; 2000mm < 4mm; 3000mm < 3mm
This is the content of the gas booster pump http://www.liqun518.com. Thank you for checking the information content of our company in your busy schedule. If you want to know more, you are welcome to call for consultation!
